Engine

• Adaptation of the throttle unit
• Quick test of exhaust camshaft control
• Quick test of intake camshaft control
• Quick test of the fuel pump (FP)
• Quick test of the fuel tank system (USA/CDN)
• Programming optimizing parameters
• Resetting the adaptation values
• Resetting the odometer particle trap
• Adaptation of the exhaust gas recirculation (EGR) valve
• Readiness code

Additive Dosing Module (ADM)

• Refilling the feed hose with additive
• Resetting the tank level gauge

Transmission Control Module (TCM)

• Calibration of position sensor (калибровку необходимо проводить если был заменен ЭБУ автоматической трансмиссии)
• Resetting adaptation
• Resetting counter oil
• Control module adaptation
• Resetting adaptation to zero

Anti-lock Brake System Mode (ABS/BCM)

• Calibration (Cars with DSTS(Dynamic stability and traction control) (функция используется для калибровки данных в ЭБУ BCM (Brake Control Module) после ремонта)

1. Steering angle, calibration
2. Lateral accelerometer calibration
3. Longitudinal accelerometer calibration
4. Pressure sensor calibration

• Check brake light switch adjustment

Drive Door Module

• Initializing the window position
• Programming the remote control setting

Passenger Door Module

• Initializing the window position

Power Seat Module

• Programming the remote control setting

Supplemental Restrain System Module (SRS)

• Calibrating the occupant weight sensor (OWS)

Central Electronic Module (CEM)

• Calibration of position sensor, GDL lamps
• Quick test of alternator function
• Resetting low voltage counters
• Resetting factory setting
• Programming the control module
• Reading off the alarm cause
• Resetting the car

Driver Information Module

• Resetting the service reminder indicator (SRI)
• Programming the remote control setting
• Testing all needles and lamps in the dashboard
• Programming the driver information module (DIM)

Phone Module (PHM)

• Reinstalling the reserve battery (функция используется только при замене новой батареи)
• Volvo On call service check
• Resetting the carphone code

Infotainment Control Module (ICM)

• Programming the infotainment control module (ICM)

1. Programming IR communication setting
2. Setting the display background
3. Setting the reverse gear engagement acoustic signal
4. Setting the functionality of kay position 0

Climate control Module

• Adjusting ECC parameters

Rear Electronic Module (REM)

• Calibrating the position sensor for Bi-Xenon lamps

2.10 OPEL

Engine

• Adjust Idle Speed
• Replace MAF sensor
• Replace precatalyst
• Replace Rail Pressure sensor
• Regeneration D. Particulate Filter
• Injector Cutoff Test
• Replace Diesel Particulate Filter
• Reset Engine Oil Life

Immobilizer

• Erase Key Set
• Program Transponder-Keys

CIM (Steering Column Module)

• Erase Transponder-Keys and Remote
• Program Transponder-Keys and Remote

Coding/Program

• ZCS/FA CODING
• Alignment EWS-DME

Service function

• Maintenance

1. CBS reset
2. Delete transport mode

• Drive

1. Diesel Electronics– Reset learning function, Adjustment programs(DDE-CAS Adjustment), Adaptation Air-mass Flow sensor,
2. EGR transmission function - Reset learning function, Clear adaptation
3. Digital Motor Electronics – Clear adaptation, CO adjustment, Learning Valvetronic limit position, DDE-CAS Adjustment, Idle speed Adjustment, Clear adaptation
4. Electronic car immobilization system – Disable/enable key
5. Engine management ME9/MED9 - DDE-CAS Adjustment, Idle speed Adjustment, Clear adaptation, Learning Valvetronic limit position, CO adjustment

• Chassis

1. Wheel-slip control system – Adjustment, steering-angle sensor
2. Dynamic Drive – Start startup, Learn sensor values

• Body

1. IHKA Integrated automatic heating/air conditioning – Run-in protection for A/C compressor
2. Instrument cluster – Reset service interval indicator
3. Light Check Module – Read out operating data
4. Transport mode – Delete transport mode

Service and Maintenance

• Perform oil change

1. Oil quality, sheet number of Standard oil
2. Oil quality, sheet number of engine oil: …

• Radio/TV/DVD coding

1. Active radio code number
2. TV/DVD Active

ECM

• Initial startup
• Control module adaptation

1. a) Detach the transport protection of control module N15/5 (electronic selector lever module control module), personalizer or activate the control module

• Read coding and/or transfer download to new control unit

ASSYST PLUS – PLUS Active Service System

• General servicing

1. Confirm overall maintenance
2. Confirm performance of individual maintenance items
3. Reset mistakenly confirmed overall maintenance
4. Reset mistakenly confirmed maintenance item
5. Enter due dates

• Control unit adaptations

1. Variant coding (Brake data, Current brake lining thickness, Special equipment, Vehicle maintenance for usa)
2. Control module reset
3. Rearrange Service memory

Transmission

• Initial startup
• Control module adaptation

1. a) SCN Coding

• Learn air conditioning
• Adaptations

1. a) Definition (функция используется для адаптации ЭБУ трансмисиии лоя оптимизации переключения передач)
2. b) Assignment of hydraulic shift elements
3. c) Important information on adaptation limit values
4. d) Display and reset of adaptation data
5. e) Performation adaptation (Transmission Control, Torque converter lockup clutch)

• Diagnosis routines

1. a) Switch off solenoid valve for torque converter lockup clutch
2. b) Switch off the incline recognition for dynamometer mode

• Read coding and/or transfer download to new control unit

DTR – Distronic

• Control module adaptation

AB – Airbag

• Initial startup
• Control module adaptation

1. a) Read coding and change if necessary
2. b) Coded vehicle data
3. Special setting

OCP – Overhead control panel

• Initial startup
• Control module adaptation

HRA-RF – Front right headlamp range control

• Control module adaptation

UCP – Upper control panel

• Control module adaptation

Rear SAM – Rear signal acquisition and actuation module

• Control module adaptation

ICM – Instrument cluster with maintenance interval display

• Control module adaptation

1. a) Clock
2. b) Reset odometer to “0” (основной одометр может быть сброшен на «0», процедуру можно выполнять несколько раз, но общий пробег который можно сбросить не превышает 250 км. Процедура невозможна для США )
3. c) Oil change

SMC – Steering column module

• Initial startup

D2B – Comand or Audio

• Initial startup
• Control module adaptation

1. a) Read coding and change if necessary

C-AAC/AAC/HEAT – Convinience automatic air conditioning

• Initial startup
• Control module adaptation

ESP – Electronic stability program

• Initial startup
• Control module adaptation

1. a) Road test
2. b) Learning processes
3. c) Resetting of variant locking

EIS – Electronic ignition switch

• Initial startup (автоматический/ручной)
• Control module adaptation

1. a) Read coding and change if necessary
2. b) Disable key or key track
3. c) Disable key or key track with workshop key
4. d) Once again authorize key or key track
5. e) Program replacement keys
6. f) Authorize control module N73 (EIS control module)
7. g) Activate control module N26/5 (Electronic steering lock control module)
8. h) Key assignment or key track assignment to a memory block number
9. i) Write of the VIN

• Read coding and/or transfer download to new control unit

LCP – Lower control panel

• Initial startup

COMAND/AUDIO – Audio50 or COMAND

• Initial startup
• Control module adaptation

DCM-FL – Door control module front left

• Initial startup
• Control module adaptation
• Read coding and/or transfer download to new control unit

TPC – Tire pressure monitor

• Initial startup
• Control module adaptation (активация/дезактивация)

Traction system ABS, ASR, ETC, ESP

• Initial startup
• Control module adaptation

1. a) Road test
2. b) Learning processes
3. c) Resetting of variant locking

PSE – Pneumatic system equipment

• Variant coding
• Initial startup
• Control module adaptation

1. a) Read coding and change if necessary

• Lower or raise head restrains

TAC – Automatic temperature control/AAC-Automatic air conditioning

• Initial startup
• Control module adaptation

1. a) Read coding and change if necessary
2. b) Special setting

ME 9.7 – Motor electronic 9.7

• Control module adaptation

Suspension

• Initial startup

ASSYST– Active Service System

• Control module adaptation

AIRmatic

• Initial startup (ручной)
• Control module adaptation

1. a) Level calibration

AHE – Trailer recognition

• Control module adaptation (активация/дезактивация)

PTS – Parktronic system

• Initial startup

Engine

• Initialising the autoadaptives

ABS

• Bleading

A/T

• Initialising the autoadaptives

Built-in system interface (BSI)

• Initialization\Learning

1. Forcing of the customer mode
2. Resetting to zero of the service mileage

04 Introduction of BASIC setting

07 Coding

10 Adaptation

11 Login procedure

15 Write VIN

Experts function

1. Instrument reset service
2. SRS reset service
3. Read PIN (II IMMO from Immobilizer box)
4. Read PIN(II IMMO from Instrument)
5. Read PIN (III IMMO from Engine)
6. Odometer read and write (Passat 1.8GSi)